Action Construction, Inc. company logo

Boiler Installation and Repair in Stamford, CT

Get a free estimate on boiler installation or repair in Stamford, CT.

Action Construction handles boiler installation and repair in Stamford, CT as the licensed plumbing contractor, covering the boiler itself and everything piped to it: expansion tanks, zone valves, circulators, near boiler piping, the vessel, and the lines running out to baseboard and radiators. We work on Navien, Lochinvar, Peerless, Burnham, and Weil McLain equipment. This is plumbing contractor work, not a general heating and cooling service call.

Why a boiler job belongs to a plumber

Boiler work is everything on the water side of a heating system,

  • from the piping out to baseboard and radiators
  • through the feed valve and its backflow preventer
  • the low water cutoff
  • the air separator and expansion tank
  • the zone valves
  • the circulators
  • the near boiler piping
  • and finally the boiler vessel itself

In a search for boiler help around Stamford, general heating and air conditioning firms make up a good share of what comes up, and those firms usually see a boiler as one appliance among many instead of a plumbing system in itself. Our company is the licensed plumbing contractor, so we install the boiler and all of the piping connected to it, and we service gas and oil fired hydronic systems correctly because we understand the water side, and not just the thermostat.

Planning a boiler replacement early

Nobody wants to replace a boiler in the dead of winter. When a unit quits then, the replacement is rushed and priced as an emergency, with no time to work out the load or fit the venting correctly. Replacing a tired boiler in the shoulder seasons, spring or fall, is a better plan than waiting for a January failure. Watch for a boiler more than 20 to 25 years old, fuel use that creeps up while comfort stays the same, an expansion tank full of water that keeps popping the relief valve, pipes beside the boiler that show corrosion, zones that heat unevenly, firing in short bursts, and corroded or leaking sections or tankless coil.

Sizing a new boiler and rebuilding the piping around it

Replacement quotes here begin with a heat loss calculation for each room, since going by what the old nameplate says would repeat a common error: older boilers around here were frequently oversized to begin with, and a properly sized modern unit uses less fuel and cycles less. The piping beside the boiler is rebuilt to the manufacturer’s specification, because joining a new boiler to corroded old piping would undermine it. Together with the placement of the circulator, the air separator, and the expansion tank, that piping protects the new unit and keeps the zones in balance. For a condensing high efficiency boiler, a low loss header or primary secondary piping supplies the minimum flow it requires every time. The price you get in writing includes the boiler, the near boiler piping, a new circulator and expansion tank where needed, the permit, the municipal inspection, and a chimney liner or venting when an old atmospheric unit comes out.

Boiler repairs and the brands whose parts we carry

Repair work for us includes

  • aquastat and control board faults
  • zones that are air bound and will not heat
  • relief valves that leak
  • a feed valve that fails to keep pressure in the system
  • pressure problems and low water cutoff trouble
  • circulators and zone valves that have failed
  • and calls with no heat

Parts for Lochinvar, Peerless, Navien, Burnham, and Weil McLain are in stock with us, which is why one visit resolves most of those calls instead of becoming a parts order and a cold weekend. Hot water that comes off the boiler through an indirect tank or a coil connects this work to water heater installation and water heater repair, and our Stamford plumbing services hub has the full list.

Steam and condensing boilers in downtown Stamford buildings

Many older multifamily buildings downtown heat with a hydronic boiler on baseboard or radiators, and some of them still run steam instead of hot water. Steam changes the sizing: the boiler is matched to the connected radiation, not to heat loss, and its Hartford loop and header have to follow the maker’s diagram, or the new boiler carries water over and hammers. Skimming the new boiler on startup and setting the automatic water feeder and the low water cutoff are part of how we get these systems quiet. Newer condo and mixed use buildings downtown and in the South End more often run high efficiency condensing boilers, which demand correctly sized venting and condensate handling that an undersized install skips.

Yearly boiler service ahead of winter

Ahead of the heating season, a hydronic boiler needs one yearly visit, and ours covers

  • looking over the circulators and zone valves
  • examining the relief valve and the venting
  • bleeding the air out of each zone
  • testing that the low water cutoff works
  • measuring the system pressure and the expansion tank charge
  • and, on oil units, cleaning and adjusting the burner and fitting a new nozzle and filter

A fault that a fall service would have caught sits behind most January no heat calls: an expansion tank that has filled with water, a circulator that is wearing out, a zone valve that sticks, a clogged condensate trap on a high efficiency unit, or a control that has drifted out of range. Set against the emergency rate for a holiday weekend call and a cold building, the visit costs a few hundred dollars. In a building with tenants, an annual service on record supports the landlord’s duty to provide heat, and several properties can be handled together on a fall schedule that has each boiler checked in one visit, ahead of the first cold night and not after the first no heat call.

Frequently Asked Questions: Boiler Installation and Repair in Stamford, CT

Is fixing a boiler plumbing work or HVAC work?

It is plumbing work. Circulators, zone valves, the expansion tank, and all of the water side piping belong to a plumber, and so does the boiler itself. A licensed plumbing contractor is the one to call for a replacement, a leak, or no heat from a hydronic system.

Which brands of boiler does your team install in Stamford?

Lochinvar, Navien, Weil McLain, Burnham, and Peerless. They run on gas or oil, and they serve baseboard, radiator, and radiant heating. To choose among them we look at whether an indirect tank off the boiler would heat water better than a separate heater, at whether a condensing unit could vent through the chimney or a sidewall, and at the distribution and fuel you have today.

Should I call an HVAC company or a plumber about my boiler?

Call a plumber for the boiler, its piping, and any install or repair on the water side. We take on the boiler and the plumbing together, not as one more line on a long list of heating services.

What does a boiler replacement cost in Stamford?

No single figure fits every house. Cost moves with the fuel, the boiler size, a cast iron versus a high efficiency condensing model, and how much piping and venting beside the boiler has to be redone. Before work begins, you get a written installed price, permit and inspection included, based on a heat loss calculation.

Is it the boiler if just one room stays cold in my building?

Rarely the boiler itself. A single cold zone tends to trace back to a zone valve that stuck, a circulator on that loop that died, air trapped in the line that has to be bled, or balancing trouble. Each is a repair we make, and the cause gets identified before any quote.

Ready to Start Your Plumbing Project in Stamford?

Need commercial construction, renovations, or plumbing services? Tell us about the project and we will set up a consultation and estimate.

Licensed & Insured | Residential & Commercial | Serving CT & NY