Action Construction, Inc. company logo

Boiler Installation and Repair in White Plains, NY

Get a free estimate on boiler installation or repair in White Plains, NY.

A boiler job in White Plains, NY involves more than the boiler. Action Construction, a licensed plumbing contractor, installs and repairs the unit and all the pipework around it: baseboard and radiator connections, expansion tanks, zone valves, circulators, and the near boiler piping. Lochinvar, Peerless, Navien, Burnham, and Weil McLain boilers are all part of our service work. What we do is plumbing contractor work rather than a general heating and cooling service call.

A boiler is a plumbing system

Boiler work belongs to the water side of a heating system, which covers

  • the circulators
  • the zone valves
  • the boiler vessel
  • the low water cutoff
  • the near boiler piping
  • the feed valve with its backflow preventer
  • the air separator and expansion tank
  • and the lines out to baseboard and radiators

Plenty of the companies that appear when you look for boiler help near White Plains are general heating and air conditioning firms, and they often treat the boiler as an appliance, not a plumbing system in its own right. We are the licensed plumbing contractor that puts in boilers and everything piped to them, and we work on gas and oil fired hydronic systems the right way because we know the water side and not just the thermostat.

How to know a boiler is due for replacement

Start with the age: a boiler past 20 to 25 years is near the end of its life. Other clues are rusted or leaking sections, or a leaking tankless coil, a unit that fires on and off in quick cycles, heat that is uneven from one zone to the next, corroded near boiler piping, an expansion tank that is waterlogged and keeps tripping the relief valve, and a fuel bill that rises with no gain in comfort. The reason to act early is cost, because a boiler that quits during a cold spell has to be replaced as an emergency, at a premium, with no time for a load calculation or for matching the venting properly. A tired unit is better replaced in the shoulder season, spring or fall.

Heat loss sizing and the piping next to the boiler

Each replacement is sized from a heat loss calculation, run room by room, because the old nameplate is a poor guide, and oversizing is common among older boilers in this area, whereas a right sized unit burns less fuel and short cycles less. Corroded runs beside the boiler are replaced, not reused, with new piping built to the maker’s specification, since the air separator, the expansion tank, and the circulator placement depend on it to guard the new boiler and keep the zones in balance. A condensing model also needs its minimum flow assured, which a low loss header or primary secondary piping does. In writing, the price lists the boiler, the permit, the municipal inspection, venting or a chimney liner where an old atmospheric unit comes out, the near boiler piping, and a circulator and expansion tank where needed.

What we repair and the brands we carry parts for

The repairs we take on include

  • calls with no heat
  • circulators that have quit and zone valves that have failed
  • pressure faults or a misbehaving low water cutoff
  • a feed valve that cannot maintain pressure
  • relief valves that leak
  • zones that are air bound and stay cold
  • and aquastat or control board faults

Parts for Navien, Weil McLain, Lochinvar, Burnham, and Peerless are kept in stock, so one visit usually finishes the job and the building does not wait out a parts order over a cold weekend. If hot water reaches you by way of an indirect tank or a coil off the boiler, see water heater installation and water heater repair, and the White Plains plumbing services hub lists the rest.

Boilers in White Plains: steam, hot water, and condensing units

Condensing boilers with high efficiency ratings are the more common choice in the newer high rises of the City Center district, and they call for correctly sized venting and condensate handling that an undersized install skips. In the neighborhoods ringing downtown, the older multifamily and single family buildings mostly heat with a hydronic boiler on baseboard or radiators, though some of the older multifamily buildings still run steam. A steam boiler is sized from the connected radiation rather than from heat loss. Its Hartford loop and header must match the maker’s diagram, or water carries over and the new boiler hammers. We skim the new boiler at startup and set the automatic water feeder and the low water cutoff so the system runs quiet.

The fall boiler service visit

The yearly visit before heating season covers

  • clearing trapped air out of the zones
  • reading the system pressure and the charge in the expansion tank
  • looking over the relief valve and the venting
  • verifying that the low water cutoff works
  • servicing the burner and swapping the nozzle and filter on oil units
  • and checking the circulators and zone valves

Most January no heat calls can be traced to something a fall visit would have turned up, whether that is an expansion tank gone waterlogged, a circulator near the end, a zone valve that sticks, a condensate trap that has plugged on a high efficiency unit, or a control that has drifted out of range. The visit costs a few hundred dollars, which is the figure to hold against an emergency rate on a holiday weekend with the building cold. Where tenants live in the building, a written record of each annual service backs up the landlord’s duty to provide heat, and for a portfolio we can schedule all the boilers together so each is checked on one fall visit, ahead of the first real cold and not after a tenant’s first call about no heat.

Frequently Asked Questions: Boiler Installation and Repair in White Plains, NY

Does boiler repair fall under plumbing or HVAC?

Plumbing covers it. The boiler, its water side pipes, circulators, zone valves, and the expansion tank all fall under the plumbing trade, which is our work. Call a licensed plumbing contractor for a new boiler, a leak, or a hydronic system that has stopped heating.

What brands of boiler do you install in White Plains?

Our brands are Navien, Peerless, Burnham, Lochinvar, and Weil McLain, in oil or gas fired models for baseboard, radiant, or radiator setups. Before choosing, we ask what piping layout and fuel you have, whether the chimney or a sidewall can vent a condensing model, and whether hot water would come more sensibly from an indirect tank on the boiler than from a water heater of its own.

Is a plumber or an HVAC company the right call for a boiler?

A plumber. The boiler, its piping, and any water side installation or repair are plumbing jobs, and we do them directly instead of treating them as a single entry among general heating services.

What should a boiler replacement cost in White Plains?

Price follows four variables. Fuel and boiler size come first, then the choice between cast iron and a condensing high efficiency unit, and last how much surrounding pipework and venting must be rebuilt. We run the heat loss calculation, then put the installed price in writing with the permit and inspection included, ahead of any work.

One room stays cold and the others are fine. Is the boiler the problem?

Most likely the boiler is fine. A cold zone usually comes from a balancing problem, an air bound line that must be bled, a failed circulator on that loop, or a stuck zone valve. We handle each repair and pin down the cause before we quote.

Ready to Start Your Plumbing Project in White Plains?

Need commercial construction, renovations, or plumbing services? Tell us about the project and we will set up a consultation and estimate.

Licensed & Insured | Residential & Commercial | Serving CT & NY